Toshiba 4200FA XT Скачать руководство пользователя | Manualshive

Страница: 49 / 68

background image

4200FA XT 80kVA Installation and Operation Manual

41

6.12 Shutdown Procedure

When turning off the UPS, the following shutdown procedure should be used.

1) Move the RUN/STOP key switch of the UPS to STOP. Operation of the inverter halts.

Output power is now provided to the load via the bypass circuit. If a power failure occurs
in the commercial power source while in this state, the UPS will lose power and power to
the load will be interrupted. The battery charging circuit and chopper circuit will remain
active.

DANGER

Do not touch the UPS terminals even though the operation switch
has been moved to the STOP position. The UPS may be supplying
power through the bypass circuit.

The LCD display shows the following message when in the Bypass operating mode:

- BYPASS OPERATION

OUTPUT VOLTAGE=208V

>CURRENT 100/100/100%

DATE (DAY) TIME

Move the MCCB power switch to Off.

Power is removed from the UPS and to any

attached loads

. All lamps are off and the LCD display shows the following message so long

as there is sufficient power to display it:

- OUTPUT SHUT DOWN -

OUTPUT VOLTAGE= 0V

CURRENT=LOW/LOW/LOW%

Emergency Power Off activation trips the MCCB and power is removed from the UPS and to
any connected loads (see Section 6.6 "EPO Function"). All LEDs are off and the LCD display
will show the following message:

- OUTPUT SHUT DOWN -

OUTPUT VOLTAGE= 0V

CURRENT=LOW/LOW/LOW%

Note:

Actual numerical values may

differ from these examples.

«
...
47
48
49
50
51
...
»

Содержание 4200FA XT





































































Отзывы:

Нет отзывов

Похожие инструкции для 4200FA XT

Бренд: ACCURAT Страницы: 48

Бренд: ACCURAT Страницы: 20

Бренд: Chloride Страницы: 60

XP Pro evolution

Бренд: INFOSEC UPS SYSTEM Страницы: 72

Z1 ZenCube EX 400

Бренд: INFOSEC UPS SYSTEM Страницы: 34

Liebert PSP500MT3-230U

Бренд: Emerson Страницы: 2

Бренд: NEC Страницы: 15

Бренд: Eaton Страницы: 22

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 13

Mobile Power System

Бренд: Jansen Medicars Страницы: 16

Бренд: Tripp Lite Страницы: 2

Бренд: Tripp Lite Страницы: 4

Бренд: Tripp Lite Страницы: 5

Бренд: Tripp Lite Страницы: 32

Inverter Series

Бренд: OPTI-UPS Страницы: 31

Бренд: Sola HD Страницы: 46

Бренд: Online USV Страницы: 129

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды