Toshiba 4200FA XT Скачать руководство пользователя | Manualshive

Страница: 41 / 68

background image

4200FA XT 80kVA Installation and Operation Manual

33

6.4

Battery Recharging

The illustration below shows the battery recharge process after a full discharge.

The recharge process typically consists of three periods. During the first period, the charging
current is maintained at approximately 20.0 amperes. This current is the maximum value that
can be used to charge the batteries (for minimal recharge time) while assuring safety and
long battery life.

In the second period, constant-voltage control starts and the current gradually decreases as
the batteries charge to the fully charged state.

In the third period, a trickle current continues to flow into the batteries to maintain the fully
charged status at the normal DC Voltage level.

A full recharge requires approximately 24 hours (90% recharge in 10 X discharge time) after
a complete discharge.

The following table shows the rated maximum and minimum battery voltages, and the charge
current for each of the sizes for 75 °F (24 °C) operation.

Rated Battery Voltages

V float

324 VDC

V min

216 VDC

I charge

20.0 Amps

«
...
39
40
41
42
43
...
»

Содержание 4200FA XT





































































Отзывы:

Нет отзывов

Похожие инструкции для 4200FA XT

Gamatronic B120US

Бренд: SolarEdge Страницы: 99

Challenger Series

Бренд: MAKELSAN Страницы: 72

Бренд: La Marche Страницы: 32

BBP-AR-1000-PSW-ONL

Бренд: Battery Backup Power Страницы: 43

Бренд: Gamatronic Страницы: 82

Бренд: Eaton Страницы: 20

Megaline Series

Бренд: LEGRAND Страницы: 2

Бренд: Xtreme Страницы: 38

Бренд: Vesta Страницы: 2

Бренд: CPS Страницы: 2

Бренд: Eaton Страницы: 40

Бренд: OPTI-UPS Страницы: 24

Бренд: Tripp Lite Страницы: 20

Бренд: Online Страницы: 16

Бренд: Online Страницы: 22

Бренд: Xtreme Power Conversion Страницы: 39

Бренд: Eaton Страницы: 10

Бренд: Trust Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды