Toro Z 440 Pro Value Series Скачать руководство пользователя страница 99

Страница: 99 / 190

5-12

Z Master Z400 Service Manual

ENGINE

Kohler V-Twin 20 hp Engine Removal

1. Remove the battery negative cable from the battery.

2. Raise the rear wheels of the machine off the ground

and support frame with jack stands. Remove both

rear wheels.

Fig 251

PICT-0267

4. Remove the 4 bolts and nuts that hold the tailpipe

guard to the right hand guard strap (Fig. 251).

19. Connect the battery negative cable.

Fig 249

PICT-0036c

c. Pull the cable housing until the throttle linkage

is in the full throttle position. Tighten the cable

clamp (Fig. 249).

3. Remove the eight bolts, washers and nuts that hold

the notched weight onto the rear of the machine.

Remove the notched weight from the rear of the

machine (Fig. 250).

Fig 250

PICT-0265

Содержание Z 440 Pro Value Series































































































































































































Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Бренды по названию

Популярные бренды

Toro Z 440 Pro Value Series, Руководство по обслуживанию

Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Бренды по названию

Популярные бренды