Toro Z 440 Pro Value Series Скачать руководство пользователя страница 137

Страница: 137 / 190

6-4

Z Master Z400 Service Manual

ELECTRICAL

The PTO Switch is located on the control panel on the

left side of the operator (Fig. 384).

Fig 384

PICT-0190

Fig 385

PTO switch test

Cont.

OFF (IN)

ON (OUT)

not used

Cont.

Open

Cont.

Open

not used

1. Disengage the PTO, set the parking brake, and turn

the ignition to OFF. Remove the key.

2. Remove the 4 screws holding the control panel to

the fuel tank.

3. Disconnect the wiring harness from the PTO switch.

4. Press in the locking tabs, on each side of the switch,

and pull the switch out of the control panel.

5. Verify that there is continuity between the

appropriate terminals in the ON and OFF positions

(Fig. 385).

Contacts inside the switch electrically connect various

terminals in both “On” and “Off” position. When the

PTO is pulled out to the ON position, current flows to

the electric clutch and it engages. When the switch is

pushed in to the OFF position, current flows through the

PTO switch to the Park Brake switch as part of the circuit

used to ensure safe starting.

Location

How It Works

Testing

Continuity?

Y = Yes

N = No

Содержание Z 440 Pro Value Series































































































































































































Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Toro Z 440 Pro Value Series, Руководство по обслуживанию, Страница: 137 / 190

Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы: