Toro Z 440 Pro Value Series страница 160 Скачать руководство пользователя

Страница: 160 / 190

7-3

Z Master Z400 Service Manual

MOWER DECKS/PTO

6. Remove the front and rear lift chains from the mower

deck (Fig. 412).

Fig 412

PICT-0126

7. Remove the bolts holding the cross brace to the

deck (Fig. 413).

Note: Check the cross brace bushings for wear.

Replace as needed.

Fig 413

PICT-0128

Fig 415

PICT-0129

12. Slide the mower deck out the right side of the unit

(Fig. 415).

Fig 414

PICT-0130

8. Secure the cross brace to the frame so it is out of

the way when removing the mower deck.

9. Raise the lift lever to the transport position.

10. Remove the 4 x 4 wood blocks from under the deck.

11. Turn the right front wheel so the castor fork is angled

forward. This will allow more clearance to slide the

mower deck out from under the frame (Fig. 414).

Содержание Z 440 Pro Value Series































































































































































































Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды

Toro Z 440 Pro Value Series, Руководство по обслуживанию

Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды