Toro Z 440 Pro Value Series страница 187 Скачать руководство пользователя

Страница: 187 / 190

7-30

Z Master Z400 Service Manual

MOWER DECKS/PTO

8. Loosen the jam nut under the rear support arm and

turn the adjustment bolt to get a measurement of 3-

1/8 to 3-1/4 inches (79 - 83mm) (Fig. 504).

Note: It is recommended that both sides of the

mower are adjusted the same distance.

9. Tighten the jam nut under the rear support arm and

tighten the bolt securing the chain to the rear support

arm.

10. Adjust the opposite side if needed.

Fig 504

fig. 57 G001924

7. If the measurements at positions

are not

correct, loosen the bolt attaching the rear chain to

the rear support arm (Fig. 504).

1. Position the right blade front-to-rear (Fig. 505).

Fig 505

fig. 58 G001041

2. Measure the right blade at the

location, from a

flat surface to the cutting edge of the blade tip (Fig.

505).

3. Record this measurement.

4. Measure the right blade at the

location, from a

level surface to the cutting edge of the blade tip

(Fig. 505).

5. Record this measurement.

6. The mower blade should be 1/4 to 3/8 inch (6 to

10mm) lower at position A than at position B (Fig.

505). If it is not correct, proceed to the following

steps.

Note: Both of the front swivels need to be adjusted

the same amount to maintain equal chain

tension and side-to-side level.

1. Rear chain

5. Adjustment bolt

2. Rear support arm

6. Front swivel

3. Bolt

7. Front support arm

4. Jam nut

Adjusting the Front-to-Rear Mower Pitch

1. Measure here from

2. Measure at A and B

blade to flat surface

Содержание Z 440 Pro Value Series































































































































































































Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды

Toro Z 440 Pro Value Series, Руководство по обслуживанию

Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды