Toro Z 440 Pro Value Series страница 142 Скачать руководство пользователя

Страница: 142 / 190

6-9

Z Master Z400 Service Manual

ELECTRICAL

The seat switch is mounted to the frame directly under

the seat (Fig. 395).

Fig 395

PICT-0198

When the seat is vacated, the switch is open and there

should be NO continuity between the two terminals.

When the seat is occupied, the switch closes and there

should be continuity between the two terminals (Fig.

396) (Deluxe suspension seat switch shown).

Fig 396

DSC-2556

When operating the unit on rough terrain, if the operator

should come off the seat momentarily, the seat delay

module will temporarily delay the engine shutting down.

1. Disconnect the switch from the wiring harness.

2. Using a VOM or test light, check first to ensure there

is no continuity between either terminal, plunger out.

3. With the plunger pushed in, there should be

continuity between the terminals.

Location

How It Works

Testing

Seat Delay Module

Purpose

Location

The seat delay module is located under the panel

assembly (Fig. 397).

Fig 397

PICT-0194

Содержание Z 440 Pro Value Series































































































































































































Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды

Toro Z 440 Pro Value Series, Руководство по обслуживанию

Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды