Toro Z 440 Pro Value Series страница 21 Скачать руководство пользователя

Страница: 21 / 190

2-12

Z Master Z400 Service Manual

SPECIFICATIONS

Cutting Decks cont.

48” (121.9cm)

52” (132.1cm)

7-Gauge Deck

44” (111.8cm)

SFS Deck

48” (121.9cm)

TF Deck

52” (132.1cm)

TF Deck

112cm (44”)

SFS Deck

132cm (52”)

TF Deck

Deck

Suspension

Deck

suspended

from machine

by four lift

chains, and

attached to

front cross

member by flat

strut arms and

cross brace.

The deck is

pulled along

the ground.

Belt Covers

Plastic HDPE

deck covers.

Attached with

swell latches.

14-gauge,

formed steel

covers with

access holes

to allow

greasing of

outer spindles

without

removal.

Attached with

draw latches.

14-gauge,

formed steel

covers with

access holes

to allow

greasing of

outer spindles

without

removal.

Attached with

draw latches.

Plastic HDPE

deck covers.

Attached with

swell latches.

Gage Wheels Three

adjustable

gage wheels

to reduce

scalping on

the front of

deck (one on

the left-hand

side and two

in the center).

Wheels

have four

adjustment

positions.

Deck suspended from machine by four lift chains, and attached to rear

wheel supports by two struts. The deck is pulled along the ground.

Plastic HDPE deck covers.

Attached with swell latches.

Three adjustable gage wheels to reduce scalping: three on front of deck (one

on left-hand side and two in center). Wheels have four adjustment positions.

Rear gage wheels are optional.

Содержание Z 440 Pro Value Series































































































































































































Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды

Toro Z 440 Pro Value Series, Руководство по обслуживанию

Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды