Toro Z 440 Pro Value Series страница 145 Скачать руководство пользователя

Страница: 145 / 190

6-12

Z Master Z400 Service Manual

ELECTRICAL

The electric clutch controls the engagement and

disengagement of the Power Take Off (PTO) pulley.

Location

The electric clutch is located on the PTO end of the

crankshaft.

The PTO clutch is composed of three major

components; the field, the clutch plate, and the friction

plate. The clutch plate always turns with the engine. The

field is a coil of wire wound around an iron core, which

acts like an electromagnet when power is applied. The

friction plate is the only piece that can slide inward and

outward on the crankshaft axis. It is spring loaded away

from contact with the clutch plate. When the clutch is

not energized, the clutch plate rests against the brake

material opposite the clutch plate. When energized the

friction plate is drawn into the clutch plate magnetically

and the two rotate as one component.

Fig 402

coil resist measure

1. Disengage the PTO, set the parking brake, turn the

ignition to the “off” position and remove the ignition

key.

2. Disconnect the clutch harness from the main

harness.

3. Set the multimeter or volt/ohm meter to check

resistance (ohms).

4. Connect the meter lead wires to the clutch wires as

shown (Fig. 402).

If the electric PTO clutch does not engage or is suspect

as the cause of an electrical problem in the PTO circuit,

use the following troubleshooting steps to determine

whether the clutch has failed or another electrical

problem exists.

Electric PTO Clutch

Purpose

How It Works

Testing

Coil Resistance Measurement

5. The meter should read around 1.84 ohms (meter

readings may vary). If the reading is above or below

these readings, the field has failed and needs to

be replaced. If the reading falls between 2-4 ohms,

measure clutch current draw.

Содержание Z 440 Pro Value Series































































































































































































Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды

Toro Z 440 Pro Value Series, Руководство по обслуживанию

Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды