manualshive.com logo in svg

Toro Z 440 Pro Value Series, Руководство по обслуживанию

Поделиться
Скачать
Toro Z 440 Pro Value Series Скачать руководство пользователя страница 120

5-33

Z Master Z400 Service Manual

5

ENGINE

b.  Reconnect the z-bend of the choke cable to 

the choke linkage (the middle hole in the choke 

plate).  The choke linkage should be in the full 

open position (up).  Tighten the cable clamp 

(Fig. 331).

 

Fig 331

 

PICT-0342

 

Fig 332

 

PICT-0293

21. Reconnect the throttle cable:

a.  Position the throttle control lever so that there is 

approximately 1/2” (12.7mm) between the lever 

and the full throttle position of the throttle slot 

(Fig. 332).

 

Fig 333

 

PICT-0343 rev

b.  Reconnect the z-bend of the throttle cable to the 

throttle linkage (the lowermost hole of the throttle 

plate). Push down on the throttle linkage to 

hold it in the wide open throttle (WOT) position. 

Tighten the cable clamp (Fig. 333).

22. Install the 6 bolts, washers and nuts holding the rear 

bumper to the frame (Fig. 334).

 

Fig 334

 

PICT-0321

23. Install the rear wheels.  Lower the machine to the 

ground.

24. Connect the battery negative cable.

Содержание Z 440 Pro Value Series































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды