Toro Z 440 Pro Value Series страница 185 Скачать руководство пользователя

Страница: 185 / 190

7-28

Z Master Z400 Service Manual

MOWER DECKS/PTO

Fig 501

fig. 49 G001678

Z 400 Series

1. Disengage the PTO, move the motion control levers

to the neutral locked position, and set the parking

brake.

2. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating

postition.

3. Remove the belt covers over the outside spindles.

4. Loosen the fixed idler arm and adjust it to relieve the

belt tension on the fixed idler pulley (Fig. 501).

5. Install the belt covers over the outside spindles.

6. Tighten the outer nut on the spring eye bolt (Fig.

500).

Note: Check the spring length. The spring should

measure 9-38

1/8 inch (238

3mm) with belt

installed. Adjust it if it does not (Fig. 500).

5. To increase the belt tension, rotate the ratchet or

breaker bar counterclockwise to move the fixed

idler arm until you feel increased resistance and the

spring-loaded idler pulley stops moving (Fig. 502).

Note: Do not increase the belt tension beyond the

point where the fixed idler arm stops.

Fig 502

fig. 50 G001679

6. While holding the belt in tension, tighten the 2 nuts

that secure the fixed idler arm.

7. Remove the ratchet or breaker bar from the square

hole in the fixed idler arm.

8. Install the belt covers over the outside spindles.

1. Fixed idler arm

4. Mower belt

2. Square hole

5. Belt guide

3. Fixed idler pulley

6. Spring-loaded idler

pulley

1. Ratchet with short

2. Square hole

extension or breaker

bar

Adjusting the Mower Belt Tension

Содержание Z 440 Pro Value Series































































































































































































Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды

Toro Z 440 Pro Value Series, Руководство по обслуживанию

Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды