Toro Z 440 Pro Value Series страница 167 Скачать руководство пользователя

Страница: 167 / 190

7-10

Z Master Z400 Service Manual

MOWER DECKS/PTO

Mower Deck Removal

9. Insert a ratchet or breaker bar with a short extension

into the square hole in the fixed idler arm. Rotate the

ratchet or breaker bar counterclockwise to move the

fixed idler arm until you feel increased resistance

and the spring-loaded idler pulley stops moving.

Note: Do not increase the belt tension beyond the

point where the fixed idler arm stops.

Tighten the nut on the slotted idler plate (Fig. 438).

Fig 438

PICT-0315

10. Tighten the pivot bolt (Fig. 439).

Fig 439

PICT-0316

Fig 441

PICT-0375

3. With a spring puller, remove the spring from the idler

arm assembly to remove tension on the belt (Fig.

441).

Fig 440

PICT-0374

Z 100 Series (44” Deck)

1. Disengage the PTO, move the motion control levers

to the neutral locked position, and set the parking

brake.

2. Lift the floor pan and remove both the right and left

side mower belt cover (Fig. 440).

Содержание Z 440 Pro Value Series































































































































































































Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды

Toro Z 440 Pro Value Series, Руководство по обслуживанию

Результаты поиска

Содержание Z 440 Pro Value Series

Отзывы:

Похожие инструкции для Z 440 Pro Value Series

Бренды по названию

Популярные бренды