TopCold Romeo Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 16

TopCold Romeo Скачать руководство пользователя страница 3

30

9.
A

ssembly

Procedures

3

T H A N K Y O U

Thank you for purchasing a Frilixa Refrigerator!

This unit has passed our strict Quality Control Inspection and meets the high standards set. You have made

a quality investment that with proper maintenance will give you years of service.

Please read the following installation and maintenance instructions before installing or using your unit. If

you have any questions, please call our Customer Service Department at

(+351) 255 490 541

.

IMPORTANT INFORMATION - PLEASE READ



Please read these instructions carefully before installing or using. If recommended procedure are not

followed, warranty claims will be denied.



Frilixa reserves the right to change specifications and product design without notice. Such revisions do

not entitle the buyer to corresponding changes, improvements, additions or replacements for previous-

ly purchased equipment.



A detailed Owners Manual with a troubleshooting guide, parts lists and additional information can be

ordered from the factory.



The following book is available at our website.

«
1
2
3
4
5
...
»

Содержание Romeo

















Отзывы:

Нет отзывов