TK TW45C Скачать руководство пользователя страница 70

Страница: 70 / 148

Work on the product

Testing the brake

TK Elevator

BA, TW45C | 6231003860 | 06/2022

Work on the product

7.1

Testing the brake

(At least once per year within the framework of the central maintenance)

Test the braking deceleration at each brake circuit

WARNING

Elevator car movement by means of specific brake release. No self-locking
effect in the case of gearless machines!

The elevator car can move in an uncontrolled manner through the shaft.

Be prepared to brake at all times.

Regulate the travel speed of the elevator car by opening/closing the
brake manually if manual brake release is present.

The movement of the elevator car must be slow (0.3 m/s).

1. Immediately deactivate the live coils and check the brake.

1. Signs indicating that maintenance work is under way must be attached to

the elevator at all landing doors.

2. All doors must be properly and adequately locked.

3. Check that no persons are in the elevator car.

4. Position the elevator car at least two floors below the top landing.

5. For the individual tests of the brake circuits of the Warner brake, ensure

that the brake magnet coils are separately connected with inrush/holding
voltage (90 V / 45 V).

6. For the single-circuit test with lever for the Mayr brake, ensure that the

brake magnet coil is connected with inrush/holding voltage (180 V / 90
V).

7. Test the brake circuit separately.

The brake of the brake circuit not being tested must remain open dur-
ing the entire test operation.
This is done by applying holding voltage to the magnet coil of the brake
circuit that is not involved.

Test the braking deceleration on one brake circuit in each case

1. Initiate normal travel (brake to be tested is opened).

2. After the rated speed has been reached, trigger an emergency stop

(brake to be tested closes).

3. Determine the deceleration value for the 1st brake circuit with the meas-

uring device.

4. Compare the measurement result with the default value.

5. Compare the measurement results with the default values.

6. Disconnect the permanent voltage supply of the continuously opened

2nd brake circuit.

Содержание TW45C





















































































































































Результаты поиска

Содержание TW45C

Отзывы:

Похожие инструкции для TW45C

Бренды по названию

Популярные бренды

TK TW45C, Руководство по эксплуатации

Результаты поиска

Содержание TW45C

Отзывы:

Похожие инструкции для TW45C

Бренды по названию

Популярные бренды