background image

3  

24 MONTH WARRANTY 

Titan Air hereby warrants its products against defects in material and workmanship for a period 

of (24) twenty four months from date of shipment. 

Start up checklist is due back within (30) thirty days of start-up or 120 days from date of delivery 

for 24 month warranty to be effective.  After (30) thirty days, and up until (60) sixty days, a (13) 
thirteen month warranty will be observed.  All warranties are null and void if start up checklist is not 
received within (60) sixty days from start-up or 120 days from date of delivery.  NO EXCEPTIONS 
WILL BE MADE. 

Titan Air  reserves the right at Titan Air’s option, to replace or repair free of charge, any part 

proven by Titan Air to be defective.  Prompt notification of defective part must be given to Titan Air  
and defective part must be returned freight prepaid within (30) thirty days of notification. 

WARRANTY INCLUDES ONLY PARTS SUPPLIED BY TITAN AIR   INCIDENTAL COSTS AND 

LABOR CHARGES SHALL BE THE RESPONSIBILITY OF OTHERS.  This warranty does not cover 
fuses, belts, filters, refrigerant or water damaged parts which are the result of improper storage or 
installation.   

This warranty is void in event the product is improperly installed and/or operated under 

conditions other than normal published ratings, improperly maintained, misused or not in compliance 
with applicable codes or not in accordance with Titan Air’s operating instructions. 

This warranty is void if attempts to correct or repair any alleged defective part or parts are made 

by unauthorized personnel without Titan Air’s written approval. 

In no event shall Titan Air be held liable for any damage, incidental or consequential, arising from 

the installation, performance or operation of the product.   

This warranty supersedes, voids, and/or is in lieu of any other verbal or written understanding 

which may not be in total accordance with this expressed warranty. 

Warranted parts must be returned to Titan Air  within 60 days to receive credit. 

Purchased components such as Steam Generators Systems, Electric Coils, Refrigerant 

Condensers, Chillers, Coils, Heat Exchangers are covered under the original equipment 
manufacturer’s warranty. 

The burner and heat exchanger is factory set at safe operating conditions, attempting to over fire 

the burner can cause damage to the exchanger, reduce its operating life, and void the warranty. 

 

Start up of equipment with power burners are to be done by burner manufacture trained 

service technicians only for heat exchanger warranty. 

Содержание TA-109































Отзывы: