Timewave PK-232 MBX Скачать руководство пользователя страница 153

Страница: 153 / 266

ARQE

Immediate Command

Mode: Command

Host: As

ARQE is an immediate command that switches the PK-232 into the ARQ-E receiving

mode.

ARQ-E is similar to 1-channel TDM, except that the 7-bit code is different.

Like TDM most ARQ-E stations send idle signals for long periods of time. The

PK-232 can only phase on ARQ-E signals that are idling so this is not a problem.

The SIGNAL Identification (SIAM) mode will identify ARQ-E signals for the user.

They are identified as "TDM ARQ-E:4" or 'TDM ARQ-E:S,' referring to 4- and

8character repetition cycles used in this mode.

ARQTmo "n"

Default: 60

Mode: AMTOR, Pactor

Host: AO

Parameters:

“n” - 0 to 250 specifies the number of seconds to send an ARQ SELCALL

before automatic transmitter shutdown.

ARQTMO sets the length of time during which your ARQ call will be sent, shutting

down automatically. As a general rule, if you can't activate another AMTOR or

Pactor station in the default time of 60 seconds, you can probably assume that

the other station can't hear your transmission.

ARQTOL “n"

Default: 3

Mode: AMTOR ARQ

Host: AO

Parameters:

“n”' 1 to 5, specifying a relative tolerance for bit boundary jitter.

ARQTOL controls the tolerance for received bit boundary jitter in AMTOR ARQ mode.

n is a number from 1 (tight tolerance) to 5 (loose tolerance). The number

signifies how far away from the expected bit transition time the actual received

transition may be, in tenths of a bit (milliseconds). If the transition occurs

further away than expected, the received block is counted as an error, even if

all three characters in the block appear to be valid AMTOR characters. The

default value of ARQTOL 3 is the equivalent of the fixed tolerance of previous

firmware releases.

ARQTOL should be set to a low number (tighter tolerance) for applications that

require nearly error-free communications. The tradeoff is that good received

character blocks are counted as bad if the bit transitions are suspect, thereby

causing retransmissions and lowering the effective character rate.

ARQTOL does not affect FEC, SELFEC or ARQ Listen modes.

2/93

A-15a

Содержание PK-232 MBX











































































































































































































































































Результаты поиска

Содержание PK-232 MBX

Отзывы:

Похожие инструкции для PK-232 MBX

Бренды по названию

Популярные бренды

Timewave PK-232 MBX, Руководство по эксплуатации

Результаты поиска

Содержание PK-232 MBX

Отзывы:

Похожие инструкции для PK-232 MBX

Бренды по названию

Популярные бренды