Timewave PK-232 MBX Скачать руководство пользователя страница 193

Страница: 193 / 266

_______________________________________________________________________________

KISSAddr "n" Default: 0

Mode: Packet Host: KA

_________________________________ Parameters: _________________________________

"n" - Is a number from 0-15 signifying the KISS address of the TNC's radio

port.

_______________________________________________________________________________

Radio port addressing is available in the high nibble of the KISS command byte.

The PK-232 compares the high nibble of the KISS command byte to KISSADDR only if

extended KISS mode is enabled. If the command does not match KISSADDR, the TNC

takes no action. Exception: the exit-KISS command $FF works no matter what the

value of KISSADDR or the status of extended KISS mode.

_______________________________________________________________________________

LAstmsg "n" Immediate Command

Mode: Packet MailDrop Host: LA

_________________________________ Parameters: _________________________________

"n" - 0 to 999 specifies the message number of the last MailDrop message.

_______________________________________________________________________________

The number 0-999 is the number of the last message sent by a remote user or the

SYSOP to the MailDrop. This command is handy for checking the last message sent

to your MailDrop system. The LASTMSG command also allows the MailDrop message

counter to be set to any value, or simply reset by setting LASTMSG 0.

_______________________________________________________________________________

LEftrite ON|OFF Default: ON

Mode: FAX Host: LR

_________________________________ Parameters: _________________________________

ON - The FAX signal is scanned from left to right

OFF - The FAX signal is scanned from right to left

_______________________________________________________________________________

Occasionally you may come across FAX images that are obviously backwards.

Turning LEFTRITE OFF will reverse the scanning direction.

_______________________________________________________________________________

LIte ON|OFF Default: ON

Mode: Packet Host: LI

_________________________________ Parameters: _________________________________

ON - The PK-232 will attempt to use the HF Packet Lite extensions.

OFF - The PK-232 uses AX.25 Level 2 Version 1.0 or 2.0 protocol.

_______________________________________________________________________________

A Packet Lite connection is established only if both stations have LITE ON.

As with the AX25L2V2 command, LITE may not be changed if the TNC is in a

connected state. Setting LITE ON overrides the AX25L2V2 setting, and the unit

acts as if AX25L2V2 were ON. See the section of the Packet Chapter (Chapter 4)

regarding Packet Lite operation and restrictions.

8/91 A-46

Содержание PK-232 MBX











































































































































































































































































Результаты поиска

Содержание PK-232 MBX

Отзывы:

Timewave PK-232 MBX, Руководство по эксплуатации, Страница: 193 / 266

Результаты поиска

Содержание PK-232 MBX

Отзывы: