Timewave PK-232 MBX Скачать руководство пользователя страница 228

Страница: 228 / 266

_______________________________________________________________________________

SQuelch ON|OFF Default: OFF

Mode: Packet Host: SQ

_________________________________ Parameters: _________________________________

ON - Your PK-232 responds to positive-going squelch voltage.

OFF - Your PK-232 responds to negative-going squelch voltage.

_______________________________________________________________________________

Normally, your PK-232 uses its CSMA (Carrier Sense Multiple Access) circuit to

decide whether or not it is clear to transmit on a packet channel. If there are

non-packet signals on the channel you're using (such as voice), you will want to

use true RF-carrier CSMA by monitoring the squelch line voltage from your radio.

If SQUELCH is OFF (default) the PK-232 inhibits transmissions when there is a

POSITIVE voltage on the Radio connectors squelch input line. When there is no

voltage or NO CONNECTION to this pin, the PK-232 allows packets to be sent.

When SQUELCH is ON, the PK-232 will inhibit packet transmissions when there is 0

volts applied to the squelch input pin on the Radio connector.

_______________________________________________________________________________

SRXall ON|OFF Default: OFF

Mode: AMTOR Host: SR

_________________________________ Parameters: _________________________________

ON - Receive ALL selective (SELFEC) transmissions.

OFF - Receive only SELCALL-addressed SELFEC transmissions.

_______________________________________________________________________________

SRXALL permits the reception of selectively coded inverse FEC signals normally

not available for decoding. Set SRXALL ON to activate this feature.

_______________________________________________________________________________

STArt "n" Default: $11 <CTRL-Q>

Mode: All Host: ST

_________________________________ Parameters: _________________________________

"n" - 0 to $7F (0 to 127 decimal) specifies an ASCII character code.

_______________________________________________________________________________

Use the START command to choose the user START character (default <CTRL-Q>) you

want to use to restart output FROM the PK-232 TO the terminal after it has been

halted by typing the user STOP character. See the XFLOW command.

_______________________________________________________________________________

STOp "n" Default: $13 <CTRL-S>

Mode: All Host: SO

_________________________________ Parameters: _________________________________

"n" - 0 to $7F (0 to 127 decimal) specifies an ASCII character code.

_______________________________________________________________________________

Use the STOP command to select the user STOP character (default <CTRL-S>) you

will use to stop output FROM the PK-232 TO the terminal. See the XFLOW command.

8/91 A-69b

Содержание PK-232 MBX











































































































































































































































































Результаты поиска

Содержание PK-232 MBX

Отзывы:

Timewave PK-232 MBX, Руководство по эксплуатации, Страница: 228 / 266

Результаты поиска

Содержание PK-232 MBX

Отзывы: