Timewave PK-232 MBX Скачать руководство пользователя страница 159

Страница: 159 / 266

_______________________________________________________________________________

Beacon EVERY|AFTER "n" Default: EVERY 0 (00 sec.)

Mode: Packet Host: BE

_________________________________ Parameters: _________________________________

EVERY - Send the beacon at regular intervals.

AFTER - Send the beacon after the specified time interval without activity.

"n" - 0 to 250 sets beacon timing in ten-second intervals.

"0" - Zero turns off the beacon (default).

_______________________________________________________________________________

The BEACON command sets the conditions under which your beacon will be sent.

A beacon frame contains the text that you've typed into the BTEXT message in a

packet addressed to the UNPROTO address. When the keyword EVERY is specified a

beacon packet is sent every "n" times ten seconds. When AFTER is specified, a

beacon is sent after "n" times ten seconds have passed without packet activity.

If you set the BEACON timing less than "90" - a value judged as too short for

busy channels - you'll see the following message at each command prompt:

WARNING: BEACON too often

_______________________________________________________________________________

BItinv "n" Default: $00

Mode: RTTY Host: BI

_________________________________ Parameters: _________________________________

"n" - 0 to $1F, (0 to 31 decimal) specifies a number to be exclusive-ORed

with every received Baudot character. BITINV 0 is plain text.

_______________________________________________________________________________

Bit inversion is used to prevent listeners from reading some commercial Baudot

transmissions. Usually either 2 or 3 bits of each character are inverted to

give the appearance of an encrypted transmission. Try different settings of

BITINV on a Baudot signal after the baud rate has been determined. If you are

interested encrypted transmissions try experimenting with the 5BIT command.

_______________________________________________________________________________

BKondel ON|OFF Default: ON

Mode: All Host: BK

_________________________________ Parameters: _________________________________

ON - The sequence <BACKSPACE><SPACE><BACKSPACE> is echoed when a character

is deleted from the input line.

OFF - The <BACKSLASH> character <\> is echoed when a character is deleted.

_______________________________________________________________________________

BKONDEL determines how character deletion is displayed in Command or Converse

mode. When BKONDEL is ON (default) the <BACKSPACE><SPACE><BACKSPACE> sequence

is produced which updates the video display screen erasing the character.

On a printing terminal the <BACKSPACE><SPACE><BACKSPACE> sequence will result in

overtyped text. Set BKONDEL OFF if you have a paper-output display, or if your

terminal does not respond to the <BACKSPACE> character <CTRL-H>. When BKONDEL

is OFF the PK-232 displays a <BACKSLASH> for each character you delete. You can

get a display of the corrected input by typing the REDISPLAY-line character.

4/91 A-20

Содержание PK-232 MBX











































































































































































































































































Результаты поиска

Содержание PK-232 MBX

Отзывы:

Timewave PK-232 MBX, Руководство по эксплуатации, Страница: 159 / 266

Результаты поиска

Содержание PK-232 MBX

Отзывы: