Timewave PK-232 MBX Скачать руководство пользователя страница 235

Страница: 235 / 266

PK-232 OPERATING MANUAL

COMMAND SUMMARY

Listed below are the UBIT functions and the default state that presently have

been assigned. The default state of each UBIT is always shown first.

UBIT 0:

ON:

The PX-232 will discard a received packet if the signal is too

weak to light the DCD LED.

OFF:

The PK-232 will receive a packet regardless of the DCD status

or the THRESHOLD control setting.

UBIT 1: OFF:

Entering the command MONITOR ON or MONITOR YES causes the

MONITOR command to be set to 4.

ON:

Entering the command MONITOR ON or MONITOR YES causes the

MONITOR command to be set to 6.

UBIT 2:

ON:

A Break signal received on the RS-232 line forces the PK-232

into Command mode from all modes except HOST mode.

OFF:

A Break signal on the RS-232-line is ignored by the PK-232.

UBIT 3: OFF: Multiple connect Packet channels are numbd-red from 0-9.

ON:

Multiple connect Packet channels are numbered A-J.

UBIT 4:

ON:

When transmitting in Baudot, the PK-232 inserts the FIGS after

a space just prior to sending any figures space><FIGS><number>).

This permits receiving stations to decode groups of figures

correctly regardless of the USOS setting.

OFF:

The PK-232 will not insert the FIGS character after each space.

MARS operators may want to set UBIT 4 OFF for literal

operation.

UBIT 5: OFF:

The PK-232 will always power up in Command Mode.

ON:

The PK-232 will remain in the last mode Converse, Command or

Transparent) provided the battery jumper enabled.

UBIT 6:

OFF:

In Packet, monitoring is disabled when in the Transparent mode.

ON:

Packet monitoring is active in the Transparent mode. MFROM,

MT0, MRPT, MONITOR, MCON, MPROTO, MSTAMP, MXMIT, CONSTAMP and

MBX are all active.

UB1T 7: OFF:

In Morse receive, the character ..-- prints as a “^”

ON:

In Morse, the character ..-- prints as a <Carriage Return>.

UBIT 8:

OFF:

In the Morse mode, the PK-232's modem is configured for

standard Al-A single-tone ON/OFF keyed Morse.

ON:

In the Morse mode, the PK-232's modem is configured for 2-tone

FSK Morse operation on both transmit and receive. WIDESHFT,

RXREV and TXREV are all active.

UBIT 9: ON: In AMTOR a received WRU character (FIGS-D) or in Pactor a

<CTRL-E> will cause the Auto-Answerback text to be sent

regardless of the setting of WRU. In AMTOR this is subject

to the setting of the CODE command.

OFF: In AMTOR and Pactor a received WRU character will have no

effect.

2/93

A-76

Содержание PK-232 MBX











































































































































































































































































Результаты поиска

Содержание PK-232 MBX

Отзывы:

Похожие инструкции для PK-232 MBX

Бренды по названию

Популярные бренды

Timewave PK-232 MBX, Руководство по эксплуатации

Результаты поиска

Содержание PK-232 MBX

Отзывы:

Похожие инструкции для PK-232 MBX

Бренды по названию

Популярные бренды