background image

1

Thank you for purchasing a Thunder Tiger Product. 
Please read all instructions and familiarize yourself with the products and controls before operation.
1. This product is not a toy. It is a high performance model product. It is important to familiarize yourself

with the model, its manual, and its construction before assembly or operation. A child operating under
the supervision of the adults is necessary.

2. Always keep this instruction manual ready at your hand for your assembling and operating reference,

even after completing the assembly.

3. Make sure all the screws are properly tightened and all the parts are checked after running the car for a

long period of time. 

4. For the best performance, it is important to make sure all the moveable parts work free without binding.
5. Do not operate model products in rain, on public roads, near crowds, near airport, or near areas with

restricted radio operation.

6. Always keep fuel away from heat and open flame. Only operate in open, well-ventilated area. Store fuel

in cool, dry area. Keep the fuel bottle cap tightly closed. Clean up any leak or excess fuel before starting
the engine.

7. This product, its parts, and its construction tools can be harmful to your health. Always exercise extreme

caution when assembling and/or operating this product. Do not touch any part of the model that rotates.

8. Check your radio frequency with the proper operating frequency of the area or country. Always check to

see if there are any modelers operating on the same frequency as yours. Also, check your radio for
proper operation before operating a model.

ITEMS INCLUDED

ITEMS REQUIRED FOR OPERATION

Power drill or a

hand held starter.

Fuel

CAUTION

Air filter oil

0.5mm/1/8"Flat-

head screwdriver.

Philips screwdriver

TOOLS INCLUDED

RX battery pack  and

battery charger  

Double sided tape

1.5mm, 2mm, 2.5mm, 3mm

Hex wrench set

5-5.5mm wrench 

7-10mm wrench

Glow plug wrench

Hex - Starter shaft

RECOMMENDED ITEMS

These items are not required for your operation but are a good idea for safety.

Protective gloves    

Safety glasses    

Thread Lock / Screw Cement

Quick fill

fuel bottle  

2ch Transmitter 

Pistol Grip or Dual Stick

For Choice

Motorbike chassis (w/

DUCATI999R body,

rider & PRO-12BK

engine Pre-Installed)

Glow plug starter and charger 

2 high torque

servos. 

Side-guards

Содержание 6301-F

















Отзывы: