background image

INSTRUCTION MANUAL

WARRANTY

Thunder Tiger Corporation guarantees this model kit to be free from defects in both material and workmanship.

The total monetary value under warranty will in no case exceed the cost of the original kit purchased. This warranty

does not cover any components damaged by use or modification. Part or parts missing from this kit must be

reported within 60 days of purchase. No part or parts will be sent under warranty without proof of purchase. To

receive part or parts under warranty, the service center must receive a proof of purchase and/or the defective part

or parts. Should you find a defective or missing part, contact the authorized Thunder Tiger Service/Distributor

nearest you. Under no circumstances can a dealer or distributor accept return of a kit if assembly has started.

1/5 SCALE DUCATI 999R NITRO POWERED R/C MOTORBIKE

NO.6301-F

Please ensure you read and fully understand all the instructions before operation.

Official Product under license of Ducati Motor Holding S.p.A.

The contents are subject to change without prior notice due to product improvements and specification changes.

Содержание 6301-F

















Отзывы: