background image

8

The RX battery pack must be fully charged before running the
motorbike.
For best results, let the RX battery pack cool before charging.
Heat may prevent the batteries from charging to full capacity and
also decreases the performance of the batteries.
Once the batteries are ready to be charged, first plug the A/C
charger into the outlet of AC power source, then plug your RX
battery pack in the charger.(The charging time is about 10-hours.
For fast charging, you may purchase one peak detection fast
charger in the hobby shop for your convenient use.)
Continue to monitor the battery as it is being charged. As soon as

the battery is fully charged, disconnect the charging jack from the battery.

Warring: 

NiMh battery pack must be recycled or disposed of properly. Do not short circuit the RX

batter pack. This may cause burns and damages to your battery pack. Never leave charging
batteries unattended.

8

CHARGING THE RECEIVER BATTERIES 

a. When using your model, always ensure the transmitter is switched on first.
b. Then, turn on the receiver. When turning off, first turn the receiver off, then the transmitter.
c. To reverse the functions of servos, use the small, white servo reverse switches located on top of

the pistol transmitter (or the inset servo reverse switches located at the center of the stick
transmitter). To trim the servos on pistol transmitter, use the large, trim levers on top and side of
the steering wheel (the top trims steering, and the side trims throttle/brake). On a stick
transmitter, the trim levers are located accordingly around the sticks

9

RADIO OPERATION

a

a

b

b

c

c

Due to its unique steering system, the following advises for the controlling should be noted,
a. First, flip the steering servo reverse switch (see 9c). The steering is basically accomplished by

changing the center of body gravity, not the turning of the forks. With the radio transmitter and
receiver on, turn the steering wheel/stick to the right. The body leans towards the right side (The
front tire/wheel should turn left ), the chassis follows, leaning to the same side. If not, flip the
steering servo reverse switch again

b.  Return the steering wheel/stick to neutral. The front tire/wheel should point straight forward. If

not, use the steering trim lever to correct it.

c. Turn the steering wheel/ stick to the left. The front tire/wheel should turn right.

10

OPERATING RADIO - STEERING FUNCTION

a

a

b

b

c

c

The RX battery pack and charger must be purchased seperately

Содержание 6301-F

















Отзывы: