THORLABS T-Cube TTC001 Скачать руководство пользователя страница 44

Страница: 44 / 45

Page 41

16005-D03

T-Cube TEC Controller

Appendix E Thorlabs Worldwide Contacts

Thorlabs verifies our compliance with the WEEE (Waste Electrical and Electronic

Equipment) directive of the European Community and the corresponding national

laws. Accordingly, all end users in the EC may return "end of life" Annex I category

electrical and electronic equipment sold after August 13, 2005 to Thorlabs, without

incurring disposal charges. Eligible units are marked with the crossed out "wheelie

bin" logo (see right), were sold to and are currently owned by a company or institute

within the EC, and are not dissembled or contaminated. Contact Thorlabs for more

information. Waste treatment is your own responsibility. "End of life" units must be

returned to Thorlabs or handed to a company specializing in waste recovery. Do not

dispose of the unit in a litter bin or at a public waste disposal site.

For technical support or sales inquiries, please visit us at

www.thorlabs.com/contact

for our most up-to-date contact information.

USA, Canada, and South America

Thorlabs, Inc.

[email protected]

Europe

Thorlabs GmbH

[email protected]

France

Thorlabs SAS

[email protected]

Japan

Thorlabs Japan, Inc.

[email protected]

UK and Ireland

Thorlabs Ltd.
[email protected]
[email protected]

Scandinavia

Thorlabs Sweden AB
[email protected]

Brazil

Thorlabs Vendas de Fotônicos Ltda.
[email protected]

China

Thorlabs China
[email protected]

Содержание T-Cube TTC001














































Результаты поиска

Содержание T-Cube TTC001

Отзывы:

Похожие инструкции для T-Cube TTC001

Бренды по названию

Популярные бренды

THORLABS T-Cube TTC001, Руководство пользователя

Результаты поиска

Содержание T-Cube TTC001

Отзывы:

Похожие инструкции для T-Cube TTC001

Бренды по названию

Популярные бренды