THORLABS T-Cube TTC001 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 45

THORLABS T-Cube TTC001 Скачать руководство пользователя страница 20

Page 17

16005-D03

T-Cube TEC Controller

4.2 Output Potentiometer Operation

The OUTPUT potentiometer is an infinite turn encoder, used to adjust the

temperature set poi nt. To increase the set point value, turn the potentiom eter

clockwise - once the maximum value (dependent upon the CUr L setting - see Section

4.3.4. and Section 6.2.) is attained, subsequent clockwise turns d o not effect the

output, however the value decreases immediately when the control is tu rned

anticlockwise. Similarly, once the set po int value has been decreased to zero,

subsequent anticlockwise turns do not effect the output, but the value increases

immediately when the control is turned clockwise.

4.3 Navigating The Menus

Pressing the ‘MODE’ button toggles the display between the Monitor Mode and the

Setup Menu.
In Monitor Mode, with the TEC current disabled, the display will be flashing the Set

Temperature. Press the Enter button to enable the TEC current. The display stops

flashing and shows the actual temperature, the current, or the difference between the

actual temperature and the set temperature. The displayed parameter is selected in

the Setup Menu - see Section 4.3.2.
When the TEC current is enabled, pressing the Enter button disables the TEC current

and the display will again flash the set temperature.
The set temperature can be chan ged by rotating the OUTPUT Knob while in the

Monitor Mode. If the T EC current is en abled, the display will temporarily switch to

show the current se t temperature and allow you to a djust it. Once the desired

temperature is displayed, press the Enter button to select it.
In the Setup Menu, the control knob will allow you to navigate through the menu.

Once the desired menu item is displayed, it can be selected by pressing the Enter

button.
Some of the men u items ha ve sub menus that can also be n avigated using the

OUTPUT Knob. Other menu items allow you to adjust a value. The values can be

adjusted by rotating the OUTPUT Knob until the desired value is displayed and then

pressing the Enter button.
Pressing the Mode button while a menu value is displayed will return you to the menu

without adjusting the current value. If in a sub menu, pressing Mode will bring you

back up to the main Setup Menu.

«
...
18
19
20
21
22
...
»

Содержание T-Cube TTC001














































Отзывы:

Нет отзывов