Theta Digital Casablanca II, Руководство пользователя

Страница: 24 / 125

14
Introduction to the User interface
WARNING !! : PLEASE READ FIRST!
In the SETUP menu, the PW button allows the user to password protect the entire SET-UP function. In the
SETUP/INPUT page 3 sub menu, the PW button allows the user to password protect the currently selected
input. The entire GLOBAL menu can be password protected via the PW button on the second GLOBAL page
and the RS232 sub menu can be password protected via the PW button in the SETUP / GLOBAL / RS232 sub
menu. When any PW button is selected, a prompt will be displayed asking the user if they are sure they want to
change the current password ( YES or NO ). If YES is selected, the current password will be displayed with the
cursor blinking on the first character, prompting the end-user to change the current password. The password
does not have to be changed at this point, the same numbers that are currently displayed can be entered, using
buttons
1 - 6 and/or A-D . Pressing A-D enters a zero. A password containing at least one zero is null, meaning
no password. Therefore, to remove a password, press A-D at least once.
Please note that there are no passwords programmed into the Casablanca II when it is initially shipped.
PLEASE REMEMBER and/or WRITE DOWN YOUR PASSWORDS! If it/they are forgotten, all access to
password protected areas will be denied!
The menu system within the Casablanca II consists of 1 to 3 layers, with the exception of the
SETUP
menu.
Some menus have multiple pages, which can be accessed simply by pressing the A/D button, with the exception
of the INPUT SELECT menu, which uses the LEFT / RIGHT buttons. When a menu has additional pages
associated with it, a right or left arrow will be displayed in the bottom right corner of the LCD. Please refer to
figures 1 and 1 for an overall view of all menus, sub menus and menu pages.
The SETUP menu contains a number of sub menus, organized by setup function. Since many configuration
parameters can be stored for each INPUT SELECT button (by input), they are accessed in one of the 3
SETUP / INPUT sub menus. Setup parameters that are not stored individually for each INPUT SELECT button
are accessed in the two SETUP / GLOBAL sub menus. All macros can be executed via the SETUP / MACROS
sub menu.
Once a parameter is selected for editing, pressing the LEVEL UP / DOWN buttons edits the parameter value,
storing it at the same time. On any page, if the LEVEL UP / DOWN buttons are not used for editing a parameter
value, they will adjust the master volume. Where the LEVEL UP / DOWN buttons are used for editing a
parameter value, the
LEVEL LEFT
/
RIGHT
buttons will adjust the master volume, with the exception of the first
BALANCE page and the pages where input select buttons and input jacks are named. In a few cases, such as
the MODE and POST PROCESS menus, simply pressing the 1 - 6 buttons makes a selection.
The function buttons are defined as the MODE , TAPE OUT , SET-UP , and BALANCE buttons. To exit a function
the same function button can be pressed multiple times to exit, or another function button can be pressed at any
time.
Before you begin
With all input options installed in a Casablanca II, there are 32 input jacks: 6 pairs of stereo analog audio, 14
digital audio, 2 AC-3 RF, 6 composite video and 4 S-video. If the optional 8 S-Video input card is installed, then
there will be 8 S-Video inputs and no composite video inputs. If the optional Multi Format/6 S-Video board in
installed, then there will be 3 Multi format video inputs and 6 S-video inputs. Each jack can be named. It is
recommended to first name each input jack that is to be used. (
SETUP / GLOBAL/JACK NAMES ). No OSD, or
on screen menus will exist when using the 15 pin multi format video output.
Each INPUT SELECT button can have up to 6 audio, 6 composite and 6 S-video jacks mapped, or assigned to
it. Input jacks should be mapped to INPUT SELECT buttons after the applicable jacks are named. The INPUT
SELECT button should also be named. There are a total of 12 INPUT SELECT s on two pages. Pressing the
LEVEL LEFT / RIGHT buttons will toggle between these two pages of 6 inputs each.
When editing parameters for a given INPUT SELECT button, the user must first press the applicable INPUT
SELECT button in the INPUT SELECT page, then press SET-UP and INPUT , then navigate to the menu
containing the desired parameter to change.
Note : The order in which input jacks are assigned to an INPUT SELECT button determines the search order.
Please refer to page 42 for additional information on source assignment (search order). When more than one
input jack is assigned to a single
INPUT SELECT button, toggling the A-D button [when the INPUT SELECT
page is active in the front panel display] will select the next assigned input jack – both audio and video.