Theta Digital Casablanca II Скачать руководство пользователя страница 121

Страница: 121 / 125

Specifications subject to change without notice.

111

Superior Quality Balanced D/A Output Card

Output Options:

Slot 1: Front Left, Front Right, Center.

Slot 1: Front Left, Front Right, Sub 1.

Slot 2: Surround Left, Surround Right, Sub 1.

Slot 3: Sub 2, Sub 3, Sub 4.

Slot 3: Sub 2, Sub 3, Surround Center.

Each output channel has a balanced (XLR) and a single-ended (RCA) output connector.

D/A Conversion:

20-bit Ladder (8X oversampling). Two DACs per channel (6 per board) for true
differential operation.

Volume Control:

Theta proprietary switched resistor network in the analog domain.

Digital Filter:

8x oversampling Theta proprietary FIR filter running on Motorola 56004 DSP (1 per
channel, 3 per board). 4x oversampling for 96KHz sources.

Single-Ended Output:

Summed from balanced signals, retains many of the advantages of the balanced
output.

Sample Rates Supported:

32KHz, 44.1 KHz, 48 KHz, 88.1 KHz, 96 KHz.

Balanced Output Specifications:

Output Impedance:

20 Ohms.

Maximum Output Level: 20 Vrms.

Frequency Response: 20 Hz-20 kHz,

0.01 dB, Ref. 1KHz.

THD+Noise:

Less than 0.0016% @ 1KHz, maximum output level.

Dynamic Range:

105dB minimum, 20KHz bandwidth, Ref. 1KHZ, A-weighted.

Signal to Noise Ratio:

105dB typical, idle channel, A-weighted.

Crosstalk:

-90dB Right - Left, -120dB Center-Left @ 20KHz.

Single-Ended Output Specifications:

Output Impedance:

10 Ohms

Maximum Output Level: 10 Vrms

Frequency Response: 20 Hz-20 kHz,

0.01 dB, Ref. 1KHz.

THD+Noise:

Less than 0.0016% @ 1KHz, maximum output level.

Dynamic Range:

105dB minimum, 20KHz bandwidth, Ref. 1KHZ, A-weighted.

Signal to Noise Ratio:

105 typical, idle channel, A-weighted.

Crosstalk:

-90dB Right - Left, -120dB Center-Left @ 20KHz

Block Diagram:

Содержание Casablanca II






























































































































Результаты поиска

Содержание Casablanca II

Отзывы:

Бренды по названию

Популярные бренды

Theta Digital Casablanca II, Руководство пользователя

Результаты поиска

Содержание Casablanca II

Отзывы:

Бренды по названию

Популярные бренды