manualshive.com logo in svg

Theta Digital Casablanca II, Руководство пользователя

Поделиться
Скачать
Theta Digital Casablanca II Скачать руководство пользователя страница 19

 

9 

Rear Panel Layout 

 

 

Figure 7 - Rear Panel Layout 

 

1. 

Main Power Switch.

  Master power switch. Disconnects AC to all circuits.  It is recommended that this be left ON 

at all times during regular use with the exception of whenever cables are connected/disconnected or when the unit 
is not going to be used for an extended period of time. 

 

2. 

AC Power

 connector: 3 wire, IEC 320 connector with an EMI filter. 

 

3. 

RS232

 DB9 and RJ45 connectors.  A Casablanca upgraded to a Casablanca II has only the DB9 connector, on 

the Main Digital Input board. 

 

4. 

Remote Power 

jack.  Activated/deactivated when associated front panel or remote button is pressed/pressed 

again. 

 

5. 

Main Power 1 

jack.  Activated/deactivated when front panel 

POWER

 button is pressed/pressed again.  All Main 

Power jacks can output a 12V pulse (variable duration) or 12VDC. 

 

6. 

Main Power 2 

jack.  Activated when front panel 

POWER

 button is pressed once, plus x seconds.  

X

 represents 

the time value that is stored in the 

SET-UP/GLOBAL/REM PWR/MTIM 

parameter.  This jack is deactivated when 

the front panel 

POWER

 button is pressed again (putting the Casablanca in Standby mode). 

 

7. 

Main Power 3 

jack. Activated when front panel 

POWER

 button is pressed once, plus two times 

x

 seconds.  

X

 

represents the time value that is stored in the 

SET-UP/GLOBAL/REM PWR/MTIM 

parameter.  This jack is 

deactivated when the front panel 

POWER

 button is pressed again (putting the Casablanca in Standby mode). 

 

8. 

Remote Extender

 jack.  An externally mounted (remote) Infrared (IR) receiver plugs into this miniature stereo 

phone jack.  (its signal must be demodulated). Please refer to Appendix C on page 108 for additional information. 

 

9. 

Power Supply Module

. 

 

10. 

Video Card

. This optional card, necessary for on-screen display, provides six composite RCA and four S-Video 

inputs, all assignable to any input select button.  Video inputs are routed to the video tape output jack using the 

TAPE

 

OUT

 button.  Only S-Video input signals can be present at the S-Video 

Main

 and/or 

Tape

 outputs.  Another 

option for this slot is a video card containing 8 S-Video inputs with 2 main and 2 tape outs.  There are no 
composite video jacks on this alternate optional card. 

 

11. 

Main Digital Input

 card.  Six Coaxial (RCA) and two TosLink inputs are provided for digital audio signals in the 

S/PDIF format at 32K, 44.1K 48K or 96KHz sampling rates.  There are two open spaces provided for optional 
AT&T and/or Theta Single Mode Laserlinque optical input modules.  There are two RCA digital Tape Out 
connectors on this card whose digital source can be selected in the 

TAPE

 

OUT

 menu. 

 

12. 

Auxiliary Digital Input

 card.  This card provides two RCA Dolby Digital (AC-3) RF inputs, one AES/EBU 

(balanced XLR) input, one BNC and one TosLink input.  Additionally there is one space provided for an optional 
AT&T or Theta Single Mode optical input. 

 

13. 

Analog Input

 card.  Six stereo RCA inputs are provided for any line level analog output devices such as VCR’s, 

laserdisc, CD and DAT players, phono preamplifiers, external D/A converters, tape decks, AM/FM tuners, etc.  
There are two pairs of analog tape outs for recording purposes, whose source can be selected in the 

TAPE OUT

 

menu. 

 

Содержание Casablanca II






























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды