Thermo Scientific 50131250 Скачать руководство пользователя страница 56

Страница: 56 / 64

Thermo Scientific Barnstead GenPure with xCAD

Ultrapure water system

15. Trouble shooting

Fault

Cause

Remedy

The system does not start

- No supply of power

- Provide power

Dispensing not possible

-  Feedwater tap is closed
-  Feedwater and rinse water
connections mixed up
- Feedwater pressure
  < 0.1 bar

-  Open feedwater tap
-  Correct the connections

-  Increase feedwater pressure

Resistance < 18.2 M

Ω

xcm

- System has a UF-module
(higher conductivity
possible)
- Ion exchange capacity
exhausted

- Replace filter cartridge
with a new one

System control no longer
reacts

- Improper operation

- Unplug the mains plug for
5 seconds

Water flows out

- Leaky hose connection

- Feedwater pressure > 6 bar

- Check and seal the hose
connection
- Install a pressure reducer

Dispensed water flow rate is
too low

- UF-Module blocked
- Pre-pressure too low
- Internal pressure too low

- Replace UF-module
- Increase pre-pressure
- Readjust pressure reducer

Wrong time or date

- Time zone
- Summer/winter time

- Reset time and date

Wrong language

- Wrong language set

- Correct language setting

Fault message:

"Limit value feed"

- Feedwater conductivity
too high
- Limiting value set too low

- Check the pretreatment

- Check and suit the limiting
value

Содержание 50131250

































































Результаты поиска

Содержание 50131250

Отзывы:

Похожие инструкции для 50131250

Бренды по названию

Популярные бренды

Thermo Scientific 50131250, Руководство по эксплуатации

Результаты поиска

Содержание 50131250

Отзывы:

Похожие инструкции для 50131250

Бренды по названию

Популярные бренды