Thermo Scientific 1500 A2 Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 88

background image

Warning

Do not operate the unit before initial operation, installation and

certification tests have been performed.

s

The installation test must be performed in accordance with the
specifications of NSF/ANSI 49. The cabinet may be operated as a Class II
biological safety cabinet, in accordance with NSF/ANSI 49, if the unit
functions listed below were verified and if the test results are within the
safety value tolerances as specified in NSF/ANSI 49, Annex F.

• Inflow velocity profile test
• Downflow velocity profile test
• HEPA filter leakage test
•  Airflow smoke pattern test
•  Site installation assessment tests
•  A repeat test must also be performed annually, after repairs to the unit

or after location changes.

• The operator should request a written test report from the authorized

service technician.

Warning

The operational safety of the unit, particularly the personnel and

product protection, are guaranteed only if all safety functions of the unit
have been tested and approved.

s

Caution

Thermo will not warrant operational safety if the unit is operated

without the required installation and certification test, or if these tests and
repeat test are not performed by adequately trained and authorized
personnel.

s

Caution

The initial operation with subsequent installation test does not

include any decontamination measures. The sample chamber and any
accessories required must be disinfected and cleaned in accordance with
the hygiene guidelines set forth for the desired application.

s

Caution

Alarms on this unit are not factory-set. Set the alarms to avoid

product loss and ensure personnel safety. Refer to Certification section.

s

1500 Series A2 3-5

Thermo Scientific

Section 3

Start-Up

Installation Tests

«
...
28
29
30
31
32
...
»

Содержание 1500 A2 Series

























































































Отзывы:

Нет отзывов

Похожие инструкции для 1500 A2 Series

Бренд: Keithley Страницы: 67

Бренд: Keithley Страницы: 23

Бренд: Keithley Страницы: 93

Бренд: Oki Страницы: 44

Бренд: Magnescale Страницы: 64

Бренд: IEMCA Страницы: 82

KID 80-IV Touch

Бренд: IEMCA Страницы: 122

Бренд: Calrec Страницы: 92

Бренд: S.R.Smith Страницы: 8

Бренд: S.R.Smith Страницы: 23

NavBoard ZipFlip

Бренд: S&S Precision Страницы: 6

LED Street Bar 16x3W RGB IP65

Бренд: Varytec Страницы: 9

Бренд: VARILITE Страницы: 8

EVENTPROFILE VL800

Бренд: Vari Lite Страницы: 34

Optica 30 Series

Бренд: Varex Imaging Страницы: 36

Бренд: Zodiac Страницы: 2

Бренд: Zipper Mowers Страницы: 37

Бренд: Zimmer Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды