Thermo Scientific 1500 A2 Series Скачать руководство пользователя страница 20

Страница: 20 / 88

The exhaust thimble connection is installed to the top of the cabinet using
an additional adapter. The threaded inserts for the retaining screws of the
adapter are pre-installed to the top of the cabinet.

Installation on a 6 ft. model:

1. Turn the unit off and disconnect it from the power source.

2. Clean the contact surfaces around the exhaust opening, and the upper

and lower contact surfaces of the adapter thoroughly to ensure that all
grease and dust residue are removed.

3. Secure the adapter to the pre-installed threaded inserts on top of the

cabinet using the supplied four retaining screws. Tighten the screws
hand-tight.

4. Secure the accessory by tightening the supplied retaining screws (M 5)

wrench-tight.

5. Using the adjustment nuts

on the sliding panel, set
the gap height to an
opening of 2 inches.

1. Place the connecting

sleeve onto the connecting
opening of the accessory
and secure it with the
screws.

2. Fit the connecting pipe

(200 mm [8 in]) of the
on-site exhaust air system
to the connecting sleeve.

3. Seal the unused

connecting opening with
the cover. Place the cover
onto the connecting
opening at the housing
and secure it with the
screws.

1500 Series A2 2-3

Thermo Scientific

Section 2

Installation

Connecting Sleeve

Exhaust System

Accessories (continued)

Thimble

Retaining

screws

Exhaust

opening

Threaded

inserts

Pipe

Sleeve

Cover

Sleeve

Opening

Adapter

Figure 2-2.

6 ft Thimble and Sleeve

Содержание 1500 A2 Series

























































































Результаты поиска

Содержание 1500 A2 Series

Отзывы:

Похожие инструкции для 1500 A2 Series

Бренды по названию

Популярные бренды

Thermo Scientific 1500 A2 Series, Руководство по эксплуатации

Результаты поиска

Содержание 1500 A2 Series

Отзывы:

Похожие инструкции для 1500 A2 Series

Бренды по названию

Популярные бренды