Thermo Scientific 1500 A2 Series Скачать руководство пользователя страница 83

Страница: 83 / 88

8-10 1500 Series A2

Thermo Scientific

Section 8

Certification Testing

• Work Opening Edge Retention:

Pass smoke around the entire outside work opening, approximately
1.5 inches (3.8 cm) away from the cabinet.

• Window Seal Test:

Pass smoke up both sides and across the top of the window opening
from inside the work area, approximately 2 inches (5 cm) from the
edges.

Acceptance:

• No smoke shall have dead spots, reflux or escape the cabinet once drawn in.

Description:

• Refer to UL 61010-1

Description:

• Verify the unit is integrated properly into the facility.

Description:

• Verify the airflow alarms will activate within 15 seconds when there is a

20% loss.

Equipment:

• Thermal Anemometer or equivalent (hotwire)

• Anemometer probe holder, part 1911325

• Shortridge ADM-870 or equivalent

• Flowhood series 8400 or equivalent

Note:

To test the function of Airflow Alarms you need to access to the

Field Certification screen. This function is reserved to Thermo Scientific
Field Service and requires a special passcode.

Acceptance:
• Unit alarm activates within 15 seconds.

Airflow Alarms

Elect. Leakage , Ground

Resistance, Polarity Tests

Site Installation

Assessment Tests

Airflow Pattern Test

(continued)

Содержание 1500 A2 Series

























































































Результаты поиска

Содержание 1500 A2 Series

Отзывы:

Похожие инструкции для 1500 A2 Series

Бренды по названию

Популярные бренды

Thermo Scientific 1500 A2 Series, Руководство по эксплуатации

Результаты поиска

Содержание 1500 A2 Series

Отзывы:

Похожие инструкции для 1500 A2 Series

Бренды по названию

Популярные бренды