Texas Instruments TMS320DM335 Скачать руководство пользователя страница 84

Страница: 84 / 172

7.7.13 Power Domain Status Register 0 (PDSTATn)

PSC Registers

www.ti.com

The power domain status n register (PDSTATn) is shown in

Figure 7-15

and described in

Table 7-18

Figure 7-15. Power Domain Status n Register (PDSTATn)

Reserved

R-0

Reserved

EMUIHB

Reserved

PORDONE

POR

Reserved

STATE

R-0

LEGEND: R = Read; n = value at reset

Table 7-18. Power Domain Status n Register (PDSTATn) Field Descriptions

Bit

Field

Value

Description

31-12

Reserved

EMUIHB

Emulation alters domain state.

Interrupt is not active.

Interrupt is active.

Reserved

PORDONE

Power_On_Reset (POR) Done status

Power domain POR is not done.

Power domain POR is done.

POR

Power Domain Power_On_Reset (POR) status.
This bit reflects the POR status for this power domain including all modules in the domain.

Power domain POR is asserted.

Power domain POR is de-asserted.

7-1

Reserved

STATE

Power Domain Status

Power domain is in the off state.

Power domain is in the on state.

Power and Sleep Controller

SPRUFX7 – July 2008

Submit Documentation Feedback

Содержание TMS320DM335













































































































































































Результаты поиска

Содержание TMS320DM335

Отзывы:

Похожие инструкции для TMS320DM335

Бренды по названию

Популярные бренды

Texas Instruments TMS320DM335, Руководство пользователя

Результаты поиска

Содержание TMS320DM335

Отзывы:

Похожие инструкции для TMS320DM335

Бренды по названию

Популярные бренды