Texas Instruments Sitara AM1335 Series Скачать руководство пользователя страница 7

Страница: 7 / 39

www.ti.com

All Errata Listed With Silicon Revision Number

Table 4. All Design Exceptions to Functional Specifications (continued)

SILICON REVISION AFFECTED

NUMBER

TITLE

1.0

2.0

2.1

RMII: 50-MHz RMII Reference Clock Output Does Not

Advisory 1.0.16

Satisfy Clock Input Requirements of RMII Ethernet PHYs

Advisory 1.0.17

VDDS_DDR: High-Power Consumption During DeepSleep0

ROM: Ethernet Boot Code Does Not Change Default

Advisory 1.0.18

Direction of RMII1 Reference Clock When Booting from

Ethernet Using RMII

DDR3: Fully-Automated Hardware READ and WRITE

Advisory 1.0.19

Leveling Not Supported

Boot: USB Boot ROM Code Overlapping Data in TXFIFO

Advisory 1.0.20

and RXFIFO

SmartReflex: Limited Support Due to Issue Described in

Advisory 1.0.21

Advisory 1.0.15

EMIF: Dynamic Voltage Frequency Scaling (DVFS) is Not

Advisory 1.0.22

Supported

Ethernet Media Access Controller and Switch Subsystem:

Advisory 1.0.23

Reset Isolation Feature is Not Supported

Boot: System Boot is Not Reliable if Reset is Asserted

Advisory 1.0.24

While Operating in OPP50

Boot: System Boot Temporarily Stalls if an Attempt to Boot

Advisory 1.0.25

from Ethernet is Not Successful

Advisory 1.0.26

I2C: SDA and SCL Open-Drain Output Buffer Issue

Advisory 1.0.27

LCDC: LIDD DMA Mode Issue

LCDC: Raster Mode, Hardware Auto Underflow Restart

Advisory 1.0.28

Does Not Work

Latch-up Performance: Latch-up Performance Limits for

Advisory 1.0.29

Silicon Revsions 1.0 and 2.0

OSC0 and OSC1: Noise Immunity Improved When Crystal

Advisory 1.0.30

Circuit is Connected Directly to PCB Digital Ground

Advisory 1.0.31

TSC_ADC: False Pen-up Interrupts

TSC_ADC: Terminals May be Temporarily Connected

Advisory 1.0.32

Together Through Internal Paths During Power-up

Sequence

USB Host: USB Low-Speed Receive-to-Transmit Inter-

Advisory 1.0.33

Packet Delay

USB2PHY: Register Accesses After a USB Subsystem Soft

Advisory 1.0.34

Reset May Lock Up the Entire System

UART: Transactions to MDR1 Register May Cause

Advisory 1.0.35

Undesired Effect on UART Operation

EMU0 and EMU1: Terminals Must Be Pulled High Before

Advisory 1.0.36

ICEPick Samples

SPRZ360F – October 2011 – Revised November 2013

Sitara™ AM335x ARM

Cortex™-A8 Microprocessors (MPUs) (Silicon

Revision 2.1, 2.0, 1.0)

Submit Documentation Feedback

Содержание Sitara AM1335 Series








































Результаты поиска

Содержание Sitara AM1335 Series

Отзывы:

Похожие инструкции для Sitara AM1335 Series

Бренды по названию

Популярные бренды

Texas Instruments Sitara AM1335 Series, Руководство пользователя

Результаты поиска

Содержание Sitara AM1335 Series

Отзывы:

Похожие инструкции для Sitara AM1335 Series

Бренды по названию

Популярные бренды