Texas Instruments Sitara AM1335 Series Скачать руководство пользователя страница 31

Страница: 31 / 39

www.ti.com

Usage Notes and Known Design Exceptions to Functional Specifications

Advisory 1.0.28

LCDC: Raster Mode, Hardware Auto Underflow Restart Does Not Work

Revisions Affected

2.1, 2.0, 1.0

Details

The hardware restart of the LCDC during a FIFO underflow condition does not work.
Setting the AUTO_UFLOW_RESTART bit in the LCDC control register has no effect.

Workarounds

This functionality can be implemented using the software reset method outlined in
Section 13.4.6, Disable and Software Reset Sequence, of the

AM335x ARM Cortex-A8

Microprocessors (MPUs) Technical Reference Manual

(literature number

SPRUH73

Below are the summarized steps to perform a software reset:

1. Write 0 to the LCDEN bit in the RASTER_CTRL register.

2. Wait for Done interrupt by polling the DONE_RAW_SET bit in the IRQSTATUS_RAW

3. Write 1 to the MAIN_RST, or DMA_RST and CORE_RST bits in the CLKC_RESET

4. Wait several clock cycles.

5. Write 0 to the MAIN_RST, or DMA_RST and CORE_RST bits in the CLKC_RESET

6. Write 1 to the LCDEN bit in the RASTER_CTRL register.

Advisory 1.0.29

Latch-up Performance: Latch-up Performance Limits for Silicon Revsions 1.0 and
2.0

Revisions Affected

2.0, 1.0

Details

Latch-up performance was improved in silicon revision 2.1 devices and the new limits
have been updated in revision F of the

AM335x ARM Cortex-A8 Microprocessors

(MPUs)

data manual (literature number

SPRS717

Table 7

provides latch-up performance limits published in previous revisions of the

AM335x data manual and these limits apply to silicon revisions 1.0 and 2.0.

Table 7. Latch-up Performance Limits - Silicon Revisions 1.0 and 2.0

PARAMETER

MIN

MAX

UNITS

Latch-up Performance

Class II (105°C)

Workarounds

Not applicable.

SPRZ360F – October 2011 – Revised November 2013

Sitara™ AM335x ARM

Cortex™-A8 Microprocessors (MPUs) (Silicon

Revision 2.1, 2.0, 1.0)

Submit Documentation Feedback

Содержание Sitara AM1335 Series








































Результаты поиска

Содержание Sitara AM1335 Series

Отзывы:

Похожие инструкции для Sitara AM1335 Series

Бренды по названию

Популярные бренды

Texas Instruments Sitara AM1335 Series, Руководство пользователя

Результаты поиска

Содержание Sitara AM1335 Series

Отзывы:

Похожие инструкции для Sitara AM1335 Series

Бренды по названию

Популярные бренды