Terex Genie S-80 SC Скачать руководство пользователя страница 72

Страница: 72 / 78

Operator's Manual

Second Edition • Second Printing

Specifications

-80 XC

™

• S

-85 XC

™

Part No. 1311085GT

Model

S-85 XC

Height, working maximum

91 ft 27.74 m

Height, platform maximum

85 ft 25.91 m

Horizontal reach, platform

maximum

74 ft 6 in 22.71 m

Maximum load capacity

660 lbs

300 kg

Maximum load capacity, restricted 1,000 lbs

454 kg

Maximum wind speed

28 mph 12.5 m/s

Platform rotation

160°

Jib rotation

133°

Platform leveling

self-leveling

Turntable rotation (degrees)

360° continuous

Turntable tailswing

5 ft 3 in

1.6 m

Height, stowed maximum

9 ft 2 in

2.8 m

Length, stowed

40 ft 7 in 12.37 m

Width, standard tires

8 ft 2 in

2.49 m

Wheelbase

9 ft 4 in

2.85 m

Ground clearance, center

15.8 in

40 cm

Ground clearance, axle

13 in

33 cm

Turning radius (inside)

12 ft

3.66 m

Turning radius (outside)

21 ft 6 in

6.55 m

Platform dimensions,

6 foot (length x width)

72 in x 30 in 182 cm x 76 cm

Platform dimensions,

8 foot (length x width)

96 in x 36 in 244 cm x 91 cm

Ambient operating temperature

-20° F to 120° F

-29° C to 49° C

Controls

12V DC proportional

AC outlet in platform

standard

System voltage

12V

Hydraulic pressure, maximum

(boom functions)

2,900 psi

200 bar

Tire size

18-625, 16 ply FF

Fuel tank capacity

35 gallons 132 liters

Hydraulic tank capacity

40 gallons 151 liters

Weight

39,500 lbs 17,917 kg

(Machine weights vary with option configurations. See

serial label for specific machine weight.)

Airborne noise emissions

Sound pressure level at ground workstation

87 dBA

Sound pressure level at platform workstation

77 dBA

Guaranteed sound power level

109 dBA

Total vibration value to which the hand/arm system is

subjected does not exceed 2.5 m/s

Highest root mean square value of weighted

acceleration to which the whole body is subjected does

not exceed 0.5 m/s

Maximum slope rating, stowed position, 4WD

Platform uphill

30% (17°)

Platform downhill

45% (24°)

Side slope

25% (14°)

Note: Slope rating is subject to ground conditions with

one person in the platform and adequate traction.

Additional platform weight may reduce slope rating.

Maximum allowable

chassis inclination

Refer to "Tilt Sensor

Activation Settings" section

Drive speeds

Drive speed, stowed

3.0 mph

40 ft/9.1 sec

4.8 km/h

12.2 m/9.1 sec

Drive speed, raised or

extended

0.5 mph

40 ft/54 sec

0.8 km/h

12.2 m/54 sec

Floor loading information

Tire load maximum

20,649 lbs

9,366 kg

Tire contact pressure

130 psi

9.14 kg/cm

896 kPa

Occupied floor pressure

395 psf

1,926 kg/m

18.9 kPa

Note: Floor loading information is approximate and does

not incorporate different option configurations. It should

be used only with adequate safety factors.
Continuous improvement of our products is a Genie

policy. Product specifications are subject to change

without notice or obligation.

Содержание Genie S-80 SC















































































Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды

Terex Genie S-80 SC, Руководство оператора

Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды