Terex Genie S-80 SC Скачать руководство пользователя страница 39

Страница: 39 / 78

Second Edition • Second Printing

Operator's Manual

Inspections

Part No. 1311085GT

-80 XC

™

• S

-85 XC

™

Test the Drive Enable System

36 Press down the foot switch and lower the

boom to the stowed position.

37 Rotate the turntable until the boom moves past

one of the non-steer wheels.

Result: The drive enable

indicator light should flash

while the boom is anywhere

in the range shown.

38 Move the drive control handle off center.

Result: The drive function should not operate.

39 Move and hold the drive enable toggle switch

to either side and slowly move the drive

control handle off center.

Result: The drive function should operate.

Note: When the drive enable system is in use, the

machine may drive in the opposite direction that

the drive and steer control handle is moved.

Use the color-coded direction

arrows on the platform controls

and the drive chassis to identify

the direction of travel.

Test Limited Drive Speed

40 Press down the foot switch.
41 Raise the boom approximately 15° above

horizontal.

42 Slowly move the control handle to full drive

position.

Result: The maximum achievable drive speed

with the boom extended should not exceed

0.73 ft/22 cm per second.

43  Lower the boom to the stowed position.
44  Extend the boom 18 inches/46 cm.
45  Slowly move the control handle to full drive

position.

Result: The maximum achievable drive speed

with the boom extended should not exceed

0.73 ft/22 cm per second.
If the drive speed with the boom raised or

extended exceeds 0.73 ft/22 cm per second,

immediately tag and remove the machine from

service.

Содержание Genie S-80 SC















































































Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Terex Genie S-80 SC, Руководство оператора, Страница: 39 / 78

Результаты поиска

Содержание Genie S-80 SC

Отзывы: