Terex Genie S-80 SC Скачать руководство пользователя страница 59

Страница: 59 / 78

Second Edition • Second Printing

Operator's Manual

Operating Instructions

Part No. 1311085GT

-80 XC

™

• S

-85 XC

™

8 The system will keep the engine on at high

RPM until the coolant temperature reaches 35

C°. The LCD screen will then display the

message "Standstill Regen Launch".

9 If the Regeneration process has begun

successfully, the regeneration process auto-

advances and the LCD screen displays the

message "Standstill Regen Active".

10 The regeneration process auto-advances and

once it is completed the LCD screen displays

the message "Regen Complete".

Aircraft Protection Package Operation

(if equipped)

If the platform bumper comes into contact with an

object, the machine will shut down and no

functions will operate.

Aircraft Protection Override

(Platform Controls)

1 Move and hold the aircraft

protection function override

switch.

2 Move the appropriate

function to move the

platform away from the

object.

Aircraft Protection Override

(Ground Controls)

1 Release all functions, including the function

enable button.

2 Press and hold the function

enable button to override

the protection.

3 Move the appropriate function to move the

platform away from the object.

Содержание Genie S-80 SC















































































Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды

Terex Genie S-80 SC, Руководство оператора

Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды