Terex Genie S-80 SC Скачать руководство пользователя страница 35

Страница: 35 / 78

Second Edition • Second Printing

Operator's Manual

Inspections

Part No. 1311085GT

-80 XC

™

• S

-85 XC

™

Do Not Operate Unless:



You learn and practice the principles of safe

machine operation contained in this operator’s

manual.
1 Avoid hazardous situations.
2 Always perform a pre-operation inspection.

3 Always perform function tests prior to

use.

Know and understand the function tests

before going on to the next section.

4 Inspect the workplace.
5 Only use the machine as it was intended.

Function Test Fundamentals

The function tests are designed to discover any

malfunctions before the machine is put into

service. The operator must follow the step-by-step

instructions to test all machine functions.
A malfunctioning machine must never be used. If

malfunctions are discovered, the machine must be

tagged and removed from service. Repairs to the

machine may only be made by a qualified service

technician, according to the manufacturer’s

specifications.
After repairs are completed, the operator must

perform a pre-operation inspection and function

tests again before putting the machine into

service.

Содержание Genie S-80 SC















































































Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды

Terex Genie S-80 SC, Руководство оператора

Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды