Terex Genie S-80 SC Скачать руководство пользователя страница 65

Страница: 65 / 78

Second Edition • Second Printing

Operator's Manual

Transport and Lifting Instructions

Part No. 1311085GT

-80 XC

™

• S

-85 XC

™

Securing to Truck or Trailer for

Transit

Always use the turntable rotation lock pin each

time the machine is transported.

1 Turntable rotation lock pin

Turn the key switch to the off position and remove

the key before transporting.
Inspect the entire machine for loose or unsecured

items.

Securing the Chassis

Use chains of ample load capacity.
Use a minimum of 6 chains.
Adjust the rigging to prevent damage to the

chains.
For diagram, refer to the Lifting Instructions.

Securing the Platform – S-80 XC

Make sure the platform is in the stowed position.
Secure the platform with a nylon strap placed

parallel to the strap guides. Do not use excessive

downward force when securing the boom section.

Securing the Platform – S-85 XC

Make sure the jib and platform are in the stowed

position.
Secure the platform with a nylon strap placed

parallel to the strap guides. Do not use excessive

downward force when securing the boom section.

Содержание Genie S-80 SC















































































Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды

Terex Genie S-80 SC, Руководство оператора

Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды