Terex Genie S-80 SC Скачать руководство пользователя страница 54

Страница: 54 / 78

Operator's Manual

Second Edition • Second Printing

Operating Instructions

-80 XC

™

• S

-85 XC

™

Part No. 1311085GT

Platform Overload Indicator Light

Light flashing indicates the platform

is overloaded. The engine will stop

and no functions will operate.
Remove weight from the platform

until the light goes off and then

restart the engine.

Platform Self-Leveling (> ±4.5° error)

When the platform level is > ±4.5° off target angle,

the following function speeds: boom up and boom

down will slow, eventually to a stop at platform

angle ±10° off target. This is correctable via

manually leveling the platform.
1 Use the platform level switch to re-position the

platform.

The platform target angle will reset.

2 Operator can resume normal operation.

Platform Out of Level (> ±10° error)

When the platform level is > +/- 10° off target

angle, then the machine malfunction indicator light

turns on and the LCD screen display fault code 98-

10.
You will need to follow the below procedures:
1 Push in and then pull out the red Emergency

Stop button.
OR
Use auxiliary power to manually level the

platform.

The platform target angle will reset.

2 Restart engine.
3 Machine malfunction indicator light should turn

OFF. LCD screen should no longer display

fault code 98-10.

4 Operator can resume normal operation.
If the machine malfunction indicator light remains

ON or if it continues to turn ON after multiple

platform target angle resets.
1 Retract and lower the boom to the stowed

position.

2 Tag and remove the machine from service

until the fault has been corrected by a qualified

service technician.

Содержание Genie S-80 SC















































































Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды

Terex Genie S-80 SC, Руководство оператора

Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды