Terex Genie S-80 SC Скачать руководство пользователя страница 17

Страница: 17 / 78

Second Edition • Second Printing

Operator's Manual

Work Area Safety

Part No. 1311085GT

-80 XC

™

• S

-85 XC

™

Do not place or attach

fixed or overhanging loads

to any part of this

machine.

Do not place ladders or

scaffolds in the platform or

against any part of this

machine.

Do not transport tools and materials unless they

are evenly distributed and can be safely handled

by person(s) in the platform.
Do not use the machine on a moving or mobile

surface or vehicle.
Be sure the tires are in good condition and the lug

nuts tightened.

Operation on Slopes Hazards

Do not drive the machine on a slope that exceeds

the maximum uphill, downhill or side slope rating

of the machine. Slope rating applies only to

machines in the stowed position.

Maximum slope rating, stowed position, 4WD
S-80/85 XC

Platform downhill

45% (24°)

Platform uphill

30% (17°)

Side slope

25% (14°)

Note: Slope rating is subject to ground conditions

with one person in the platform and adequate

traction. Additional platform weight may reduce

slope rating. See Driving on a Slope in the

Operating Instructions section.

Содержание Genie S-80 SC















































































Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды

Terex Genie S-80 SC, Руководство оператора

Результаты поиска

Содержание Genie S-80 SC

Отзывы:

Похожие инструкции для Genie S-80 SC

Бренды по названию

Популярные бренды