manualshive.com logo in svg

Temescal BCD-2800, Руководство по установке и эксплуатации

Поделиться
Скачать
Temescal BCD-2800 Скачать руководство пользователя страница 14

Section 1: Introduction and Site Prep. Checklist

FC/BCD-2800 Facility and Installation Guide

FC/BCD-2800 F & I Guide

1-4

0101-8603-0, Rev. F

Compressed Gases:

 For additional details, see section 2.3.

Vent Gas:

 Clean Dry Air (CDA) and/or Nitrogen (N

2

) (recommended)

  

60 to 120 psig (4.14 to 8.27 bar)

Compressed Air for Pneumatics:

  90 to 120 psig (6.21 to 8.27 bar)

Note: Pneumatics air pressure must be at least 10 psi greater 
than the maximum hot or cold water pressure.

Helium:  

One bottle, 99.999% pure.

Optional Process Gas:  

Argon, 99.995% minimum purity

1 to 4 sccm, for FC ion beam source without PBN, or
3 to 7 sccm, for FC ion beam source with PBN

Electrical: 

For additional information, see sections 2.4.

Main System (Drop #1)

208 VAC, 50/60 Hz, 3-phase 4-wire, 150 A, or
400 VAC, 50/60 Hz, 3-phase 5-wire wye, 90 A

HV Power Supply (Drop #2)

 (Select one power supply only)

208-V CV-6SLX

, 208 VAC, 50/60 Hz, 3-phase delta (4-wire), 30 A

400-V CV-6SLX

, 400 VAC, 50/60 Hz, 3-phase wye (5-wire, with

neutral), 20 A

208-V CV-12SLX, 

208 VAC, 50/60 Hz, 3-phase delta (4-wire), 50 A

400-V CV-12SLX, 

400 VAC, 50/60 Hz, 3-phase wye (5-wire, with

neutral) 30 A

Ground:

System requires good earth ground, low impedance to RF as well as DC

currents. For illustrations and additional details, see section 2.5.

Site Preparation and Installation Instructions

: Section 3 of this F&I Guide has

been read and understood.

Specification of Cable and Helium Line Lengths

Use this section of the checklist to specify the lengths of the nominal, component-to-
component route of helium lines, power and control/data cables, and 3”-wide copper
ground strap in your installation. Temescal will add length as appropriate for service
loops. Helium lines, power cables, and control/data cables are available in 10-ft.
increments from 10 ft. to 70 ft.

NOTE

Specified cable/helium line lengths should reflect actual routing as
anticipated in your installation, not the shortest distances between the
connection points on the various components. For each cable or line,
enter a length that is the nearest multiple of 10 ft. above the
anticipated cable/line run.

Содержание BCD-2800







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды