manualshive.com logo in svg

Tektronix TDSUSB2, Руководство пользователя

Поделиться
Скачать
Tektronix TDSUSB2 Скачать руководство пользователя страница 27

Installation 

The following figure shows signals before performing the deskew procedure with 
a single edge: 
 

 

Figure 1: Signals before deskew 

4. 

To start the application from a supported oscilloscope, select File> Run 
Application> USB2.0 Test Package or Analyze>USB2.0 Test Package from 
the menu bar of the oscilloscope. 

5. 

Select Utilities> Deskew. 

6. 

Set the channel Source in the From area to Ch1. The Source waveform is the 
reference point to which the remaining channels are deskewed. 

7. 

Set the channel Source in the To area to Ch2, to deskew the channel. 

8. 

Select the Reference Level for Ch1 and set the reference value. The 
reference level is the percentage level of the waveform from which to take 
the edges to deskew.  

9. 

Select the Reference Level in the To area for Ch2 and set the reference 
value. 

TDSUSB2 Universal Serial Bus Measurement Package 

13

10. 

Select the Hysteresis in the From area for Ch1. Hysteresis helps to ignore 
the noise level in the waveform.  

     

Содержание TDSUSB2



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды