Tektronix TDSUSB2 Скачать руководство пользователя страница 220

Страница: 220 / 250

Measurement Algorithms

Figure 121: Equipment setup for Low Speed Signal Quality for HUB Downstream

Full Speed Signal Quality HUB Downstream Setup

To set up the equipment for Full Speed Signal Quality Downstream test, follow
these steps:

Set the S6 switch to the Init position.

Use the adapters to connect the A receptacle from Device SQ test section
(marked DUT) of the test fixture to the USB2.0 Low Speed device.

Connect Ch1 of the D+

probe to the D+ pins on the Device SQ section of the

test fixture.

Connect Ch2 of the D–

probe to the D– pins on the Device SQ section of the

test fixture.

Connect the Init port of the Device SQ section of the test fixture to any

port

of the unit under test (hub) using the USB cable.

Select the measurement and select the

command button to run the

application.

Select OK after acquiring a waveform. Verify that it is a correct waveform.

206

TDSUSB2 Universal Serial Bus Measurement Package

Содержание TDSUSB2



























































































































































































































































Результаты поиска

Содержание TDSUSB2

Отзывы:

Бренды по названию

Популярные бренды

Tektronix TDSUSB2, Руководство пользователя

Результаты поиска

Содержание TDSUSB2

Отзывы:

Бренды по названию

Популярные бренды