manualshive.com logo in svg

Tektronix TDSUSB2, Руководство пользователя

Поделиться
Скачать
Tektronix TDSUSB2 Скачать руководство пользователя страница 152

Application Examples 

Chirp Measurement 

Specifying the Equipment-Chirp 

The following equipment is needed to test Chirp measurement: 

 

Tektronix digital oscilloscope 

 

TDSUSB2 application  

 

TDSUSBF compliance test fixture 

 

Two P6245 or TAP1500 single-ended probes 

Typical Equipment Setup-Chirp 

The section used for this device test is Device SQ in the test fixture. To set up the 
equipment for the Chirp test, follow these steps: 

1. 

Set the S6 switch to the Init position. 

2. 

Use a standard length of the USB cable with an A plug on one end and a B 
plug on the other end. 

3. 

 Connect one end of the cable to the B receptacle socket connector on the 
Init port of Device SQ section and the other end to the host port A socket.  

4. 

Connect the A receptacle from the Device SQ test port to the unit under test 
(device).  

5. 

Connect the single-ended probes of the oscilloscope to the D+

 

and D– pins.  

6. 

Select the measurement and select the 

 button to run the application. 

7. 

Run the HS Electrical Test Tool on the connected host.  Enumerate the unit 
under test (device) and observe the chirp signal on the oscilloscope.  Rather 
than enumerating the device, an alternative method to generate the chirp 
signal is to disconnect and reconnect the unit under test (device) to the port.  

 

138 

TDSUSB2 Universal Serial Bus Measurement Package

 

Содержание TDSUSB2



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды