manualshive.com logo in svg

Tektronix TDSUSB2, Руководство пользователя

Поделиться
Скачать
Tektronix TDSUSB2 Скачать руководство пользователя страница 146

Application Examples 

 

Reset from High Speed Measurement 

Specifying the Equipment-Reset from High Speed Measurement 

The following equipment is needed for Reset from High Speed measurement: 

 

Tektronix digital oscilloscope 

 

TDSUSB2 application  

 

TDSUSBF compliance test fixture 

 

Two P6245 or TAP1500 single-ended probes 

Typical Equipment Setup-Reset from High Speed Measurement 

To set up the Device SQ in the test fixture for the Reset from High Speed test, 
follow these steps: 

1. 

Set the S6 switch to the Init position. 

2. 

Use a standard length of the USB cable with an A plug on one end and a B 
plug on the other end. 

3. 

Connect one end of the cable to the B receptacle socket connector on the Init 
port of the Device SQ section and the other end to the host port A socket. 

4. 

Connect the A receptacle from the Device SQ test port to the unit under test 
(device). 

5. 

Connect the single-ended probes of the oscilloscope to the D+ and D– pins. 

6. 

Select the Reset from High Speed from the application, configure its options 
and select the Run button to run the application. 

7. 

Select OK after acquiring a waveform. Verify that it is a correct waveform. 

 

132 

TDSUSB2 Universal Serial Bus Measurement Package

 

Содержание TDSUSB2



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды