manualshive.com logo in svg

Tektronix TDSUSB2, Руководство пользователя

Поделиться
Скачать
Tektronix TDSUSB2 Скачать руководство пользователя страница 22

Getting Started 

Compatibility 

For information on oscilloscope compatibility, refer to the 

*

Optional 

Applications Software on Windows-Based Oscilloscopes Installation Manual

, 

Tektronix part number 071-1888-XX. The manual is also available as a PDF file. 
The dynamic range of the probes used for Low Speed and Full Speed testing 
should be at least ± 8 volts. For High Speed testing, the dynamic range should be 
± 2 volts. 

*For a current list of compatible instruments, see the Software and Drivers 
category in the Tektronix Web site

 

Requirements and Restrictions 

You must install Java Run-Time Environment V1.4.2_02 on the supported 
oscilloscope.  

The application uses the Math1 channel for Low Speed and Full Speed mode of 
operation. You will lose any information that you have stored in the Math1 
channel. 

You cannot restore the oscilloscope settings if you select File> Exit from the 
application. 

Accessories 

The application includes the following standard accessories: 

 

Optional Application Software on Windows-Based Instruments CD–ROM 

 

Optional Application Software on Windows-Based Instruments Installation 
Manual 

 

TDSUSB2 Universal Serial Bus Measurements Package Reference 

 

TDSUSBF USB2.0 Compliance Test Fixture Instructions  

 

TDSUSBF USB2.0 Compliance Test Fixture  

Optional Accessories 

 

DG2040 Data Generator (for receiver sensitivity) 

 

AWG610 Arbitrary Waveform Generator 

 

P6248 Differential probes 

 

8 

TDSUSB2 Universal Serial Bus Measurement Package

 

Содержание TDSUSB2



























































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды