Troubleshooting
6–78
CSA8000 & TDS8000 Instruments and Sampling Modules
Table 6–7: BIOS error messages (Cont.)
Error message
Explanation
On Board Parity Error
A parity error occurred in onboard memory. This error is followed by
an address.
Parity Error
A parity error occurred in onboard memory at an unknown address.
NVRAM/CMOS/PASSWORD cleared by Jumper
NVRAM, CMOS, and passwords have been cleared. The system
should be powered down and the jumper removed.
<CTRL_N> Pressed
CMOS is ignored and NVRAM is cleared. User must enter Setup.
BIOS Beep Codes
When an error occurs during the power on self test (POST), the BIOS displays an
error message describing the problem. The BIOS also issues a beep code (one
long tone followed by two short tones) during POST if the video configuration
fails (a faulty video card or no card installed) or if an external ROM module does
not properly checksum to zero.
An external ROM module (for example, a video BIOS) can also issue audible
errors, usually consisting of one long tone followed by a series of short tones. For
more information on the beep codes, check the documentation for the device.
There are several POST routines that issue a POST terminal error and shut down
the system if they fail. Before shutting down the system, the terminal-error
handler issues a beep code (see Table 6–8) signifying the test point error, writes
the error to I/O port 80h, attempts to initialize the video, and writes the error in
the upper left corner of the screen (using both monochrome and color adapters).
If the POST completes normally, the BIOS issues one short beep before passing
control to the operating system.
Содержание CSA8000 Series
