TekTone Tek-CARE120 Скачать руководство пользователя страница 37

Страница: 37 / 40

When a call is placed, it appears in the list view on the home screen of the NC415AV as shown below.

Up to three calls are shown at the same time. If more than three calls are active on the system, a scroll
arrow will appear at the bottom of the list. Calls are displayed sorted based on priority and time.

To view more details about a call, touch a call in the list. The

Details

screen will appear as shown

below.

The details screen displays information about the alarming station, the type of call, the resident name,
and more.

Staff requests

Stat

Attend

, and

Status

can also be placed from the details screen by touching

the associated button.

Once a status is selected, the button on the details screen changes color, and the status annunciates on
the system.

If a status is annunciating, the

Status

button on the right side of the screen turns red to notify staff. Act-

ive statuses may be viewed by touching the

Status

button.

IL992 Tek-CARE120 Installation Manual

Using the Tek-CARE120 System

Содержание Tek-CARE120






































Результаты поиска

Содержание Tek-CARE120

Отзывы:

Похожие инструкции для Tek-CARE120

Бренды по названию

Популярные бренды

TekTone Tek-CARE120, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Tek-CARE120

Отзывы:

Похожие инструкции для Tek-CARE120

Бренды по названию

Популярные бренды